Proud to be CanadianProudly Canadian since 1968

English Français Español
Proud to be CanadianProudly Canadian since 1968

Atlas Copco Jumbo Drill - CM785D


Telephone: +1-705-566-8190
Fax: +1-705-566-6680

Manufacturer: Atlas Copco - Epiroc
Asset Number: N/A

Type: CM/785D/899 2401866

Serial Number: USSG78396FQ

Diesel Power 328

Rated Voltage 24 V

Gross Weight: 23814

Engine hours showing 2212 hours

ECM replaced at 30629

Total Machine Hours: 32841

Recent Reported Work Done:

New Rod Changer beam and arms in summer 2015

Compressor done at 12000 hours

Rotary head at 15000 hours

Engine done at 20,000 hours

New Undercarriage complete summer of 2014

The Following Inspection was done July 19, 2016

Machine was observed running and Drilling and appeared an good working order other than below notes of normal wear. Machine was in use till parked in present condition.

Front End Drill Attachment

Presently equipped with 4” ITH Hammer

6.3 to 7 Meter drill depth

Base of boom swing cylinder pin lock is welded- play in pin

Boom hoist cylinder damp very little

Boom hoist cylinder chrome has pitting

Base of boom bracket has been welded

Fatigue cracks in feed 4 at bottom

Middle wear strip on feed need replacing

Rod changer hyd cylinder leaking

Rod changing clamp bent

Rod charger clamp bracket bent

Little hyd cylinder for changer guard missing

Hoses on front end fair 65%

Hose reels at top of feed needs replacing

One centralizer jaw worn


Front window cracked

Wiper held on tie strap

Bottom seat cushion needs replacing

Floor mat worn through

Instrument Panel cracked

Rear Heating Duct missing

Front Heating Louvers missing

Light and Wiper Panel loose

Dirt Shields (boots) on Hand Controls needs replacing

Bolts missing RH Console

Loose wiring back of Cab

Loose wiring under seat

Lincoln auto lube pump loose on bracket

Fire suppression system

Fast fuel

Engine and Inside Engine Compartment


Engine is very dry

Alt guard is loose and bent

Exhaust leak at band clamp

Heat shield torn off

Engine coolant level ok

Rad cap not locking properly

Supply line to air tank from oil separator leaking

Engine oil ok, engine level ok

Hydraulic Fan Pump bracket loose and one bolt broken

Electrical Harness above Hydraulic Tank look burnt

Hose at Regulator disconnected

4 x Rads need cleaning

1 Rad Guard Spoke broken

Drive RH Hydraulic Pump dry

Drive LH Hydraulic Pump wet -  Hose above pump leaking on it

Needs good cleaning of Air Compressor Screw Housing and hydraulic pump area

Stump Pans would need to be removed



14" pads

3/4" Height of Grouse

Chains ITM 90% good

Idler 90%

TCR 75%

Bottom roller 85%

7 bottom rollers

Full track guard

Sprockets 85%

Track -  Leveling Hydraulic Cylinder dry

LH Undercarriage same as RH

Under Belly of Machine

3x Stump Pans under engine bent and bolts missing on 2 Stump Pans

Inspection plate under hydraulic tank bent

LH Rear Car Body hit

OAL Dimensions: 10' Wide X 36' Long X 13' Tall

Undercarriage 11'4"

20' back of machine to front of U/C

99" outside of tracks to outside of tracks

See this unit operate on

McDowell YouTube Channel

Ask about this product
Image of McDowell Equippment Logo

2018 Kingsway Blvd.
Sudbury, ON P3B 4J8

Stay informed...

Please let us know your first name.
Please let us know your email address.
Invalid Input

McDowell Equipment - Copyright © 2021